2SC4226-R23 bipolar transistor — Specifications & Equivalents

About the 2SC4226-R23

The 2SC4226-R23 is an NPN bipolar transistor with a collector–emitter voltage (V_CEO) rating of 12 V, a continuous collector current (I_C) of 0.1 A and a DC current gain (h_FE) of minimum 40. It can dissipate up to 0.15 W and is rated to a junction temperature of 150 °C. It is supplied in the SOT323 package.

At a glance

• Type: NPN bipolar transistor
• Max collector–emitter voltage (V_CEO): 12 V
• Max collector current (I_C): 0.1 A
• DC current gain (h_FE): minimum 40
• Transition frequency (f_T): 3000 MHz
• Power dissipation (P_D): 0.15 W
• Max junction temperature (T_J): 150 °C
• Package: SOT323
• Manufacturer: Multi-source (JIS registered part number)

Typical applications

Judging from its ratings the 2SC4226-R23 is generally applied in RF and high-speed switching stages and small-signal amplification and general-purpose switching.

A transition frequency (f_T) of 3000 MHz indicates the frequency range over which useful current gain remains available.

The quoted current gain of minimum 40 determines the base drive needed: divide your target collector current by the minimum h_FE, not the typical figure, when sizing the base resistor.

Biasing and absolute maximum ratings

Absolute-maximum breakdown limits are V_CEO 12 V, V_CBO 20 V and V_EBO 3 V (magnitudes). The emitter–base rating is the easiest to overlook and is often only a few volts, so protect the junction against reverse drive.

Dissipation is capped at 0.15 W, and that figure assumes the datasheet's mounting and ambient conditions — derate it for your own thermal design.

Choosing a replacement for the 2SC4226-R23

A drop-in substitute for the 2SC4226-R23 must be the same NPN type and offer a collector–emitter rating of at least 12 V, a collector current rating of at least 0.1 A, current gain in the same ballpark as minimum 40 and a transition frequency of at least 3000 MHz for the same bandwidth.

Mechanically, check the replacement against the SOT323 footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.

Because 2SC4226-R23 is a JIS-registered part number rather than one vendor's proprietary series, it is produced by several manufacturers. Datasheet figures vary slightly between them, so check the datasheet of the brand you actually buy — this also makes like-for-like sourcing easier.

Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.

Frequently asked questions

What is the 2SC4226-R23?

The 2SC4226-R23 is an NPN bipolar junction transistor (BJT). It is rated for 12 V collector-emitter and 0.1 A continuous collector current.

What is the maximum voltage of the 2SC4226-R23?

Maximum collector-emitter voltage (Vceo) is 12 V, and collector-base (Vcbo) is 20 V.

How much current can the 2SC4226-R23 handle?

Continuous collector current is rated at 0.1 A, with dissipation limited to 0.15 W.

What is the hFE of the 2SC4226-R23?

DC current gain (hFE) is quoted as minimum 40. Size base drive from the minimum value so the transistor saturates fully across production spread.

What package does the 2SC4226-R23 come in?

It is listed in SOT323. Verify the pinout of the specific variant, as one outline can carry different pin assignments.

What can I use to replace the 2SC4226-R23?

This page lists 17 candidate equivalents matched on electrical ratings and package. Any replacement should meet or exceed the original voltage, current and dissipation figures and use a compatible drive level.