P1403EK MOSFET — Specifications & Equivalents
About the P1403EK
The P1403EK is a P-channel MOSFET with a drain–source voltage (VDS) rating of 30 V, a continuous drain current (ID) of 10 A and an on-resistance (RDS(on)) of 0.014 Ω. It can dissipate up to 2.5 W and is rated to a junction temperature of 150 °C. It is supplied in the PDFN5X6P package.
At a glance
- Type: P-channel MOSFET
- Max drain–source voltage (VDS): 30 V
- Max continuous drain current (ID): 10 A
- On-resistance (RDS(on)): 0.014 Ω
- Power dissipation (PD): 2.5 W
- Max junction temperature (TJ): 150 °C
- Package: PDFN5X6P
Typical applications
With its 30 V drain–source rating the P1403EK sits in the low-voltage class of switching MOSFETs, typically found in 12 V and 24 V automotive and industrial rails, synchronous buck converters, load switching and reverse-polarity protection and H-bridges for small motors.
The low 0.014 Ω on-resistance keeps conduction loss down, which suits synchronous rectification and continuous high-current paths.
Gate drive and switching notes
Keep gate–source voltage within the ±25 V maximum; exceeding it punctures the gate oxide and destroys the device permanently.
Switching behaviour is characterised by a rise time of 16 ns and an output capacitance (Coss) of 410 pF, which together with the gate drive determines switching loss and the practical upper frequency limit.
Choosing a replacement for the P1403EK
A drop-in substitute for the P1403EK must be the same P-channel type and offer a drain–source rating of at least 30 V, a continuous drain current rating of at least 10 A and an on-resistance no higher than 0.014 Ω if efficiency and heat matter.
Mechanically, check the replacement against the PDFN5X6P footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the P1403EK?
The P1403EK is a P-channel MOSFET (metal-oxide-semiconductor field-effect transistor). It is rated for 30 V drain-source and 10 A continuous drain current.
What is the maximum voltage of the P1403EK?
The P1403EK has a maximum drain-source voltage (Vds) of 30 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the P1403EK handle?
It is rated for 10 A of continuous drain current, with power dissipation limited to 2.5 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the P1403EK?
On-resistance (Rds(on)) is 0.014 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the P1403EK come in?
It is listed in PDFN5X6P. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the P1403EK?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | MOSFET |
|---|---|
| Channel Type | P -Channel |
| Drain-Source Voltage (Vds) | 30 V |
| Gate-Source Voltage (Vgs) | 25 V |
| Drain Current (Id) | 10 A |
| Drain-Source On-Resistance (Rds) | 0.014 |
| Rise Time (tr) | 16 nS |
| Output Capacitance (Coss) | 410 pF |
| Junction Temperature (Tj) | 150 °C |
| Package | PDFN5X6P |
| Power Dissipation (Pd) | 2.5 W |
Equivalent & Replacement Parts
No verified equivalents are listed for P1403EK yet.