P0160AI MOSFET — Specifications & Equivalents
About the P0160AI
The P0160AI is an N-channel MOSFET with a drain–source voltage (VDS) rating of 600 V, a continuous drain current (ID) of 1 A and an on-resistance (RDS(on)) of 12 Ω. It can dissipate up to 28 W and is rated to a junction temperature of 150 °C. It is supplied in the TO251 package.
At a glance
- Type: N-channel MOSFET
- Max drain–source voltage (VDS): 600 V
- Max continuous drain current (ID): 1 A
- On-resistance (RDS(on)): 12 Ω
- Power dissipation (PD): 28 W
- Max junction temperature (TJ): 150 °C
- Package: TO251
Typical applications
With its 600 V drain–source rating the P0160AI sits in the high-voltage (offline) class of switching MOSFETs, typically found in primary-side switching in offline SMPS (flyback, forward and quasi-resonant), active PFC boost stages, half-bridge and full-bridge inverters, induction heating and electronic ballasts and BLDC and AC motor drives. The rating leaves usable margin above the ~325 V DC bus obtained by rectifying 230 VAC mains, which is why this class dominates offline power supplies.
At 1 A it is aimed at small-signal and light-load switching rather than power conversion.
On-resistance of 12 Ω is relatively high, so this part is better suited to low duty-cycle or low-current switching than to continuous high-current conduction.
Gate drive and switching notes
Keep gate–source voltage within the ±30 V maximum; exceeding it punctures the gate oxide and destroys the device permanently.
Switching behaviour is characterised by a rise time of 20 ns and an output capacitance (Coss) of 58 pF, which together with the gate drive determines switching loss and the practical upper frequency limit.
Choosing a replacement for the P0160AI
A drop-in substitute for the P0160AI must be the same N-channel type and offer a drain–source rating of at least 600 V, a continuous drain current rating of at least 1 A and an on-resistance no higher than 12 Ω if efficiency and heat matter.
Mechanically, check the replacement against the TO251 footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the P0160AI?
The P0160AI is an N-channel MOSFET (metal-oxide-semiconductor field-effect transistor). It is rated for 600 V drain-source and 1 A continuous drain current.
What is the maximum voltage of the P0160AI?
The P0160AI has a maximum drain-source voltage (Vds) of 600 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the P0160AI handle?
It is rated for 1 A of continuous drain current, with power dissipation limited to 28 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the P0160AI?
On-resistance (Rds(on)) is 12 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the P0160AI come in?
It is listed in TO251. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the P0160AI?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | MOSFET |
|---|---|
| Channel Type | N -Channel |
| Drain-Source Voltage (Vds) | 600 V |
| Gate-Source Voltage (Vgs) | 30 V |
| Drain Current (Id) | 1 A |
| Drain-Source On-Resistance (Rds) | 12 |
| Rise Time (tr) | 20 nS |
| Output Capacitance (Coss) | 58 pF |
| Junction Temperature (Tj) | 150 °C |
| Package | TO251 |
| Power Dissipation (Pd) | 28 W |
Equivalent & Replacement Parts
No verified equivalents are listed for P0160AI yet.