IRL1004 MOSFET — Specifications & Equivalents
Manufacturer: Commonly produced by International Rectifier (now Infineon)
About the IRL1004
The IRL1004 is an N-channel MOSFET with a drain–source voltage (VDS) rating of 40 V, a continuous drain current (ID) of 130 A and an on-resistance (RDS(on)) of 0.0065 Ω. It can dissipate up to 200 W and is rated to a junction temperature of 175 °C. It is supplied in the TO220 package.
At a glance
- Type: N-channel MOSFET
- Max drain–source voltage (VDS): 40 V
- Max continuous drain current (ID): 130 A
- On-resistance (RDS(on)): 0.0065 Ω
- Power dissipation (PD): 200 W
- Max junction temperature (TJ): 175 °C
- Package: TO220
- Manufacturer: Commonly produced by International Rectifier (now Infineon)
Typical applications
With its 40 V drain–source rating the IRL1004 sits in the low-voltage class of switching MOSFETs, typically found in 12 V and 24 V automotive and industrial rails, synchronous buck converters, load switching and reverse-polarity protection and H-bridges for small motors.
The 130 A current rating puts it in high-current territory, where conduction loss (I² × RDS(on)) and thermal design usually matter more than switching loss. Budget for adequate copper area and a heatsink.
The low 0.0065 Ω on-resistance keeps conduction loss down, which suits synchronous rectification and continuous high-current paths.
Gate drive and switching notes
Keep gate–source voltage within the ±16 V maximum; exceeding it punctures the gate oxide and destroys the device permanently.
Switching behaviour is characterised by a rise time of 210 ns and an output capacitance (Coss) of 1480 pF, which together with the gate drive determines switching loss and the practical upper frequency limit.
Choosing a replacement for the IRL1004
A drop-in substitute for the IRL1004 must be the same N-channel type and offer a drain–source rating of at least 40 V, a continuous drain current rating of at least 130 A and an on-resistance no higher than 0.0065 Ω if efficiency and heat matter.
Mechanically, check the replacement against the TO220 footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the IRL1004?
The IRL1004 is an N-channel MOSFET (metal-oxide-semiconductor field-effect transistor). It is rated for 40 V drain-source and 130 A continuous drain current.
What is the maximum voltage of the IRL1004?
The IRL1004 has a maximum drain-source voltage (Vds) of 40 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the IRL1004 handle?
It is rated for 130 A of continuous drain current, with power dissipation limited to 200 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the IRL1004?
On-resistance (Rds(on)) is 0.0065 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the IRL1004 come in?
It is listed in TO220. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the IRL1004?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | MOSFET |
|---|---|
| Channel Type | N -Channel |
| Drain-Source Voltage (Vds) | 40 V |
| Gate-Source Voltage (Vgs) | 16 V |
| Drain Current (Id) | 130 A |
| Drain-Source On-Resistance (Rds) | 0.0065 |
| Rise Time (tr) | 210 nS |
| Output Capacitance (Coss) | 1480 pF |
| Junction Temperature (Tj) | 175 °C |
| Package | TO220 |
| Power Dissipation (Pd) | 200 W |
Equivalent & Replacement Parts
No verified equivalents are listed for IRL1004 yet.