IRFP244 MOSFET — Specifications & Equivalents
Manufacturer: Commonly produced by International Rectifier (now Infineon)
About the IRFP244
The IRFP244 is an N-channel MOSFET with a drain–source voltage (VDS) rating of 250 V, a continuous drain current (ID) of 15 A and an on-resistance (RDS(on)) of 0.28 Ω. It can dissipate up to 150 W and is rated to a junction temperature of 150 °C. It is supplied in the TO247AC package.
At a glance
- Type: N-channel MOSFET
- Max drain–source voltage (VDS): 250 V
- Max continuous drain current (ID): 15 A
- On-resistance (RDS(on)): 0.28 Ω
- Power dissipation (PD): 150 W
- Max junction temperature (TJ): 150 °C
- Package: TO247AC
- Manufacturer: Commonly produced by International Rectifier (now Infineon)
Typical applications
With its 250 V drain–source rating the IRFP244 sits in the medium-high-voltage class of switching MOSFETs, typically found in telecom and industrial DC rails, boost and flyback converters, LED and backlight drivers and power-factor-correction stages. Common where the bus sits well above 100 V but below rectified mains.
Gate drive and switching notes
Keep gate–source voltage within the ±20 V maximum; exceeding it punctures the gate oxide and destroys the device permanently.
Switching behaviour is characterised by a rise time of 49 ns and an output capacitance (Coss) of 320 pF, which together with the gate drive determines switching loss and the practical upper frequency limit.
Choosing a replacement for the IRFP244
A drop-in substitute for the IRFP244 must be the same N-channel type and offer a drain–source rating of at least 250 V, a continuous drain current rating of at least 15 A and an on-resistance no higher than 0.28 Ω if efficiency and heat matter.
Mechanically, check the replacement against the TO247AC footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the IRFP244?
The IRFP244 is an N-channel MOSFET (metal-oxide-semiconductor field-effect transistor). It is rated for 250 V drain-source and 15 A continuous drain current.
What is the maximum voltage of the IRFP244?
The IRFP244 has a maximum drain-source voltage (Vds) of 250 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the IRFP244 handle?
It is rated for 15 A of continuous drain current, with power dissipation limited to 150 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the IRFP244?
On-resistance (Rds(on)) is 0.28 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the IRFP244 come in?
It is listed in TO247AC. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the IRFP244?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | MOSFET |
|---|---|
| Channel Type | N -Channel |
| Drain-Source Voltage (Vds) | 250 V |
| Gate-Source Voltage (Vgs) | 20 V |
| Drain Current (Id) | 15 A |
| Drain-Source On-Resistance (Rds) | 0.28 |
| Rise Time (tr) | 49 nS |
| Output Capacitance (Coss) | 320 pF |
| Junction Temperature (Tj) | 150 °C |
| Package | TO247AC |
| Power Dissipation (Pd) | 150 W |
Equivalent & Replacement Parts
No verified equivalents are listed for IRFP244 yet.