BS107PT MOSFET — Specifications & Equivalents
About the BS107PT
The BS107PT is an N-channel MOSFET with a drain–source voltage (VDS) rating of 200 V, a continuous drain current (ID) of 0.12 A and an on-resistance (RDS(on)) of 28 Ω. It can dissipate up to 0.5 W and is rated to a junction temperature of 150 °C. It is supplied in the ELINE package.
At a glance
- Type: N-channel MOSFET
- Max drain–source voltage (VDS): 200 V
- Max continuous drain current (ID): 0.12 A
- On-resistance (RDS(on)): 28 Ω
- Power dissipation (PD): 0.5 W
- Max junction temperature (TJ): 150 °C
- Package: ELINE
Typical applications
With its 200 V drain–source rating the BS107PT sits in the medium-high-voltage class of switching MOSFETs, typically found in telecom and industrial DC rails, boost and flyback converters, LED and backlight drivers and power-factor-correction stages. Common where the bus sits well above 100 V but below rectified mains.
At 0.12 A it is aimed at small-signal and light-load switching rather than power conversion.
On-resistance of 28 Ω is relatively high, so this part is better suited to low duty-cycle or low-current switching than to continuous high-current conduction.
Gate drive and switching notes
Keep gate–source voltage within the ±20 V maximum; exceeding it punctures the gate oxide and destroys the device permanently.
Choosing a replacement for the BS107PT
A drop-in substitute for the BS107PT must be the same N-channel type and offer a drain–source rating of at least 200 V, a continuous drain current rating of at least 0.12 A and an on-resistance no higher than 28 Ω if efficiency and heat matter.
Mechanically, check the replacement against the ELINE footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the BS107PT?
The BS107PT is an N-channel MOSFET (metal-oxide-semiconductor field-effect transistor). It is rated for 200 V drain-source and 0.12 A continuous drain current.
What is the maximum voltage of the BS107PT?
The BS107PT has a maximum drain-source voltage (Vds) of 200 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the BS107PT handle?
It is rated for 0.12 A of continuous drain current, with power dissipation limited to 0.5 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the BS107PT?
On-resistance (Rds(on)) is 28 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the BS107PT come in?
It is listed in ELINE. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the BS107PT?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | MOSFET |
|---|---|
| Channel Type | N -Channel |
| Drain-Source Voltage (Vds) | 200 V |
| Gate-Source Voltage (Vgs) | 20 V |
| Drain Current (Id) | 0.12 A |
| Drain-Source On-Resistance (Rds) | 28 |
| Junction Temperature (Tj) | 150 °C |
| Package | ELINE |
| Power Dissipation (Pd) | 0.5 W |
Equivalent & Replacement Parts
No verified equivalents are listed for BS107PT yet.