BFR30 JFET — Specifications & Equivalents
Manufacturer: Multi-source (Pro Electron registered part number)
About the BFR30
The BFR30 is an N-channel JFET with a drain–source voltage (VDS) rating of 25 V, a continuous drain current (ID) of 0.01 A and an on-resistance (RDS(on)) of 2000 Ω. It can dissipate up to 0.225 W and is rated to a junction temperature of 150 °C. It is supplied in the SOT23 package.
At a glance
- Type: N-channel JFET
- Max drain–source voltage (VDS): 25 V
- Max continuous drain current (ID): 0.01 A
- On-resistance (RDS(on)): 2000 Ω
- Power dissipation (PD): 0.225 W
- Max junction temperature (TJ): 150 °C
- Package: SOT23
- Manufacturer: Multi-source (Pro Electron registered part number)
Typical applications
With its 25 V drain–source rating the BFR30 sits in the very-low-voltage class of switching MOSFETs, typically found in battery protection and power-path switching, point-of-load converters and logic-level load switching in portable devices.
At 0.01 A it is aimed at small-signal and light-load switching rather than power conversion.
On-resistance of 2000 Ω is relatively high, so this part is better suited to low duty-cycle or low-current switching than to continuous high-current conduction.
Choosing a replacement for the BFR30
A drop-in substitute for the BFR30 must be the same N-channel type and offer a drain–source rating of at least 25 V, a continuous drain current rating of at least 0.01 A and an on-resistance no higher than 2000 Ω if efficiency and heat matter.
Mechanically, check the replacement against the SOT23 footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Because BFR30 is a Pro Electron-registered part number rather than one vendor's proprietary series, it is produced by several manufacturers. Datasheet figures vary slightly between them, so check the datasheet of the brand you actually buy — this also makes like-for-like sourcing easier.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the BFR30?
The BFR30 is an N-channel junction field-effect transistor (JFET). It is rated for 25 V drain-source and 0.01 A continuous drain current.
What is the maximum voltage of the BFR30?
The BFR30 has a maximum drain-source voltage (Vds) of 25 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the BFR30 handle?
It is rated for 0.01 A of continuous drain current, with power dissipation limited to 0.225 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the BFR30?
On-resistance (Rds(on)) is 2000 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the BFR30 come in?
It is listed in SOT23. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the BFR30?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | JFET |
|---|---|
| Channel Type | N -Channel |
| Drain-Source Voltage (Vds) | 25 V |
| Drain Current (Id) | 0.01 A |
| Drain-Source On-Resistance (Rds) | 2000 |
| Output Capacitance (Coss) | 1.5 pF |
| Junction Temperature (Tj) | 150 °C |
| Package | SOT23 |
| Power Dissipation (Pd) | 0.225 W |
Equivalent & Replacement Parts
No verified equivalents are listed for BFR30 yet.