3LP01S MOSFET — Specifications & Equivalents
About the 3LP01S
The 3LP01S is a P-channel MOSFET with a drain–source voltage (VDS) rating of 30 V, a continuous drain current (ID) of 0.1 A and an on-resistance (RDS(on)) of 10.4 Ω. It can dissipate up to 0.15 W and is rated to a junction temperature of 150 °C. It is supplied in the SMCP package.
At a glance
- Type: P-channel MOSFET
- Max drain–source voltage (VDS): 30 V
- Max continuous drain current (ID): 0.1 A
- On-resistance (RDS(on)): 10.4 Ω
- Power dissipation (PD): 0.15 W
- Max junction temperature (TJ): 150 °C
- Package: SMCP
Typical applications
With its 30 V drain–source rating the 3LP01S sits in the low-voltage class of switching MOSFETs, typically found in 12 V and 24 V automotive and industrial rails, synchronous buck converters, load switching and reverse-polarity protection and H-bridges for small motors.
At 0.1 A it is aimed at small-signal and light-load switching rather than power conversion.
On-resistance of 10.4 Ω is relatively high, so this part is better suited to low duty-cycle or low-current switching than to continuous high-current conduction.
Gate drive and switching notes
Keep gate–source voltage within the ±10 V maximum; exceeding it punctures the gate oxide and destroys the device permanently.
Switching behaviour is characterised by a rise time of 55 ns and an output capacitance (Coss) of 5.7 pF, which together with the gate drive determines switching loss and the practical upper frequency limit.
Choosing a replacement for the 3LP01S
A drop-in substitute for the 3LP01S must be the same P-channel type and offer a drain–source rating of at least 30 V, a continuous drain current rating of at least 0.1 A and an on-resistance no higher than 10.4 Ω if efficiency and heat matter.
Mechanically, check the replacement against the SMCP footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the 3LP01S?
The 3LP01S is a P-channel MOSFET (metal-oxide-semiconductor field-effect transistor). It is rated for 30 V drain-source and 0.1 A continuous drain current.
What is the maximum voltage of the 3LP01S?
The 3LP01S has a maximum drain-source voltage (Vds) of 30 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the 3LP01S handle?
It is rated for 0.1 A of continuous drain current, with power dissipation limited to 0.15 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the 3LP01S?
On-resistance (Rds(on)) is 10.4 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the 3LP01S come in?
It is listed in SMCP. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the 3LP01S?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | MOSFET |
|---|---|
| Channel Type | P -Channel |
| Drain-Source Voltage (Vds) | 30 V |
| Gate-Source Voltage (Vgs) | 10 V |
| Drain Current (Id) | 0.1 A |
| Drain-Source On-Resistance (Rds) | 10.4 |
| Rise Time (tr) | 55 nS |
| Output Capacitance (Coss) | 5.7 pF |
| Junction Temperature (Tj) | 150 °C |
| Package | SMCP |
| Power Dissipation (Pd) | 0.15 W |
Equivalent & Replacement Parts
No verified equivalents are listed for 3LP01S yet.