30P55 MOSFET — Specifications & Equivalents
About the 30P55
The 30P55 is a P-channel MOSFET with a drain–source voltage (VDS) rating of 55 V, a continuous drain current (ID) of 30 A and an on-resistance (RDS(on)) of 0.04 Ω. It can dissipate up to 90 W and is rated to a junction temperature of 150 °C. It is supplied in the TO252 package.
At a glance
- Type: P-channel MOSFET
- Max drain–source voltage (VDS): 55 V
- Max continuous drain current (ID): 30 A
- On-resistance (RDS(on)): 0.04 Ω
- Power dissipation (PD): 90 W
- Max junction temperature (TJ): 150 °C
- Package: TO252
Typical applications
With its 55 V drain–source rating the 30P55 sits in the low-voltage class of switching MOSFETs, typically found in 12 V and 24 V automotive and industrial rails, synchronous buck converters, load switching and reverse-polarity protection and H-bridges for small motors.
The low 0.04 Ω on-resistance keeps conduction loss down, which suits synchronous rectification and continuous high-current paths.
Gate drive and switching notes
Keep gate–source voltage within the ±20 V maximum; exceeding it punctures the gate oxide and destroys the device permanently.
Switching behaviour is characterised by an output capacitance (Coss) of 240 pF, which together with the gate drive determines switching loss and the practical upper frequency limit.
Choosing a replacement for the 30P55
A drop-in substitute for the 30P55 must be the same P-channel type and offer a drain–source rating of at least 55 V, a continuous drain current rating of at least 30 A and an on-resistance no higher than 0.04 Ω if efficiency and heat matter.
Mechanically, check the replacement against the TO252 footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the 30P55?
The 30P55 is a P-channel MOSFET (metal-oxide-semiconductor field-effect transistor). It is rated for 55 V drain-source and 30 A continuous drain current.
What is the maximum voltage of the 30P55?
The 30P55 has a maximum drain-source voltage (Vds) of 55 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the 30P55 handle?
It is rated for 30 A of continuous drain current, with power dissipation limited to 90 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the 30P55?
On-resistance (Rds(on)) is 0.04 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the 30P55 come in?
It is listed in TO252. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the 30P55?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | MOSFET |
|---|---|
| Channel Type | P -Channel |
| Drain-Source Voltage (Vds) | 55 V |
| Gate-Source Voltage (Vgs) | 20 V |
| Drain Current (Id) | 30 A |
| Drain-Source On-Resistance (Rds) | 0.04 |
| Output Capacitance (Coss) | 240 pF |
| Junction Temperature (Tj) | 150 °C |
| Package | TO252 |
| Power Dissipation (Pd) | 90 W |
Equivalent & Replacement Parts
No verified equivalents are listed for 30P55 yet.