2SK1070 JFET — Specifications & Equivalents
Manufacturer: Multi-source (JIS registered part number)
About the 2SK1070
The 2SK1070 is an N-channel JFET with a drain–source voltage (VDS) rating of 22 V, a continuous drain current (ID) of 0.05 A and an on-resistance (RDS(on)) of 80 Ω. It can dissipate up to 0.15 W and is rated to a junction temperature of 150 °C. It is supplied in the MPAK package.
At a glance
- Type: N-channel JFET
- Max drain–source voltage (VDS): 22 V
- Max continuous drain current (ID): 0.05 A
- On-resistance (RDS(on)): 80 Ω
- Power dissipation (PD): 0.15 W
- Max junction temperature (TJ): 150 °C
- Package: MPAK
- Manufacturer: Multi-source (JIS registered part number)
Typical applications
With its 22 V drain–source rating the 2SK1070 sits in the very-low-voltage class of switching MOSFETs, typically found in battery protection and power-path switching, point-of-load converters and logic-level load switching in portable devices.
At 0.05 A it is aimed at small-signal and light-load switching rather than power conversion.
On-resistance of 80 Ω is relatively high, so this part is better suited to low duty-cycle or low-current switching than to continuous high-current conduction.
Choosing a replacement for the 2SK1070
A drop-in substitute for the 2SK1070 must be the same N-channel type and offer a drain–source rating of at least 22 V, a continuous drain current rating of at least 0.05 A and an on-resistance no higher than 80 Ω if efficiency and heat matter.
Mechanically, check the replacement against the MPAK footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Because 2SK1070 is a JIS-registered part number rather than one vendor's proprietary series, it is produced by several manufacturers. Datasheet figures vary slightly between them, so check the datasheet of the brand you actually buy — this also makes like-for-like sourcing easier.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the 2SK1070?
The 2SK1070 is an N-channel junction field-effect transistor (JFET). It is rated for 22 V drain-source and 0.05 A continuous drain current.
What is the maximum voltage of the 2SK1070?
The 2SK1070 has a maximum drain-source voltage (Vds) of 22 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the 2SK1070 handle?
It is rated for 0.05 A of continuous drain current, with power dissipation limited to 0.15 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the 2SK1070?
On-resistance (Rds(on)) is 80 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the 2SK1070 come in?
It is listed in MPAK. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the 2SK1070?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | JFET |
|---|---|
| Channel Type | N -Channel |
| Drain-Source Voltage (Vds) | 22 V |
| Drain Current (Id) | 0.05 A |
| Drain-Source On-Resistance (Rds) | 80 |
| Junction Temperature (Tj) | 150 °C |
| Package | MPAK |
| Power Dissipation (Pd) | 0.15 W |
Equivalent & Replacement Parts
No verified equivalents are listed for 2SK1070 yet.