2N4391CSM JFET — Specifications & Equivalents
Manufacturer: Multi-source (JEDEC registered part number)
About the 2N4391CSM
The 2N4391CSM is an N-channel JFET with a drain–source voltage (VDS) rating of 40 V, a continuous drain current (ID) of 0.15 A and an on-resistance (RDS(on)) of 30 Ω. It can dissipate up to 0.35 W and is rated to a junction temperature of 150 °C. It is supplied in the LCC1 package.
At a glance
- Type: N-channel JFET
- Max drain–source voltage (VDS): 40 V
- Max continuous drain current (ID): 0.15 A
- On-resistance (RDS(on)): 30 Ω
- Power dissipation (PD): 0.35 W
- Max junction temperature (TJ): 150 °C
- Package: LCC1
- Manufacturer: Multi-source (JEDEC registered part number)
Typical applications
With its 40 V drain–source rating the 2N4391CSM sits in the low-voltage class of switching MOSFETs, typically found in 12 V and 24 V automotive and industrial rails, synchronous buck converters, load switching and reverse-polarity protection and H-bridges for small motors.
At 0.15 A it is aimed at small-signal and light-load switching rather than power conversion.
On-resistance of 30 Ω is relatively high, so this part is better suited to low duty-cycle or low-current switching than to continuous high-current conduction.
Choosing a replacement for the 2N4391CSM
A drop-in substitute for the 2N4391CSM must be the same N-channel type and offer a drain–source rating of at least 40 V, a continuous drain current rating of at least 0.15 A and an on-resistance no higher than 30 Ω if efficiency and heat matter.
Mechanically, check the replacement against the LCC1 footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Because 2N4391CSM is a JEDEC-registered part number rather than one vendor's proprietary series, it is produced by several manufacturers. Datasheet figures vary slightly between them, so check the datasheet of the brand you actually buy — this also makes like-for-like sourcing easier.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the 2N4391CSM?
The 2N4391CSM is an N-channel junction field-effect transistor (JFET). It is rated for 40 V drain-source and 0.15 A continuous drain current.
What is the maximum voltage of the 2N4391CSM?
The 2N4391CSM has a maximum drain-source voltage (Vds) of 40 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the 2N4391CSM handle?
It is rated for 0.15 A of continuous drain current, with power dissipation limited to 0.35 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the 2N4391CSM?
On-resistance (Rds(on)) is 30 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the 2N4391CSM come in?
It is listed in LCC1. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the 2N4391CSM?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | JFET |
|---|---|
| Channel Type | N -Channel |
| Drain-Source Voltage (Vds) | 40 V |
| Drain Current (Id) | 0.15 A |
| Drain-Source On-Resistance (Rds) | 30 |
| Output Capacitance (Coss) | 14 pF |
| Junction Temperature (Tj) | 150 °C |
| Package | LCC1 |
| Power Dissipation (Pd) | 0.35 W |
Equivalent & Replacement Parts
No verified equivalents are listed for 2N4391CSM yet.