10N90 MOSFET — Specifications & Equivalents
About the 10N90
The 10N90 is an N-channel MOSFET with a drain–source voltage (VDS) rating of 900 V, a continuous drain current (ID) of 10 A and an on-resistance (RDS(on)) of 1.15 Ω. It can dissipate up to 183 W and is rated to a junction temperature of 150 °C. It is available in TO-247 and TO-3P packages, so confirm the pinout of the exact variant you order.
At a glance
- Type: N-channel MOSFET
- Max drain–source voltage (VDS): 900 V
- Max continuous drain current (ID): 10 A
- On-resistance (RDS(on)): 1.15 Ω
- Power dissipation (PD): 183 W
- Max junction temperature (TJ): 150 °C
- Package: TO-247, TO-3P
Typical applications
With its 900 V drain–source rating the 10N90 sits in the high-voltage (offline) class of switching MOSFETs, typically found in primary-side switching in offline SMPS (flyback, forward and quasi-resonant), active PFC boost stages, half-bridge and full-bridge inverters, induction heating and electronic ballasts and BLDC and AC motor drives. The rating leaves usable margin above the ~325 V DC bus obtained by rectifying 230 VAC mains, which is why this class dominates offline power supplies.
On-resistance of 1.15 Ω is relatively high, so this part is better suited to low duty-cycle or low-current switching than to continuous high-current conduction.
Gate drive and switching notes
Keep gate–source voltage within the ±30 V maximum; exceeding it punctures the gate oxide and destroys the device permanently.
Switching behaviour is characterised by a rise time of 54 ns and an output capacitance (Coss) of 245 pF, which together with the gate drive determines switching loss and the practical upper frequency limit.
Choosing a replacement for the 10N90
A drop-in substitute for the 10N90 must be the same N-channel type and offer a drain–source rating of at least 900 V, a continuous drain current rating of at least 10 A and an on-resistance no higher than 1.15 Ω if efficiency and heat matter.
Mechanically, check the replacement against the TO-247 and TO-3P footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the 10N90?
The 10N90 is an N-channel MOSFET (metal-oxide-semiconductor field-effect transistor). It is rated for 900 V drain-source and 10 A continuous drain current.
What is the maximum voltage of the 10N90?
The 10N90 has a maximum drain-source voltage (Vds) of 900 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the 10N90 handle?
It is rated for 10 A of continuous drain current, with power dissipation limited to 183 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the 10N90?
On-resistance (Rds(on)) is 1.15 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the 10N90 come in?
It is listed in TO-247 and TO-3P. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the 10N90?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | MOSFET |
|---|---|
| Channel Type | N -Channel |
| Drain-Source Voltage (Vds) | 900 V |
| Gate-Source Voltage (Vgs) | 30 V |
| Drain Current (Id) | 10 A |
| Drain-Source On-Resistance (Rds) | 1.15 |
| Rise Time (tr) | 54 nS |
| Output Capacitance (Coss) | 245 pF |
| Junction Temperature (Tj) | 150 °C |
| Package | TO-247 TO-3P |
| Power Dissipation (Pd) | 183 W |
Equivalent & Replacement Parts
No verified equivalents are listed for 10N90 yet.