10N45 MOSFET — Specifications & Equivalents
About the 10N45
The 10N45 is an N-channel MOSFET with a drain–source voltage (VDS) rating of 450 V, a continuous drain current (ID) of 10 A and an on-resistance (RDS(on)) of 0.6 Ω. It can dissipate up to 150 W and is rated to a junction temperature of 150 °C. It is supplied in the TO-3 package.
At a glance
- Type: N-channel MOSFET
- Max drain–source voltage (VDS): 450 V
- Max continuous drain current (ID): 10 A
- On-resistance (RDS(on)): 0.6 Ω
- Power dissipation (PD): 150 W
- Max junction temperature (TJ): 150 °C
- Package: TO-3
Typical applications
With its 450 V drain–source rating the 10N45 sits in the medium-high-voltage class of switching MOSFETs, typically found in telecom and industrial DC rails, boost and flyback converters, LED and backlight drivers and power-factor-correction stages. Common where the bus sits well above 100 V but below rectified mains.
Gate drive and switching notes
Keep gate–source voltage within the ±20 V maximum; exceeding it punctures the gate oxide and destroys the device permanently.
Switching behaviour is characterised by a rise time of 50 ns and an output capacitance (Coss) of 600 pF, which together with the gate drive determines switching loss and the practical upper frequency limit.
Choosing a replacement for the 10N45
A drop-in substitute for the 10N45 must be the same N-channel type and offer a drain–source rating of at least 450 V, a continuous drain current rating of at least 10 A and an on-resistance no higher than 0.6 Ω if efficiency and heat matter.
Mechanically, check the replacement against the TO-3 footprint and confirm the pin order — parts sharing a package outline do not always share a pinout.
Where the application switches inductive loads or runs near the voltage limit, keep extra headroom rather than choosing a part that only just meets the original numbers.
Frequently asked questions
What is the 10N45?
The 10N45 is an N-channel MOSFET (metal-oxide-semiconductor field-effect transistor). It is rated for 450 V drain-source and 10 A continuous drain current.
What is the maximum voltage of the 10N45?
The 10N45 has a maximum drain-source voltage (Vds) of 450 V. Treat this as an absolute maximum and design with margin, especially when switching inductive loads.
How much current can the 10N45 handle?
It is rated for 10 A of continuous drain current, with power dissipation limited to 150 W. Real-world capability depends on your heatsinking and ambient temperature.
What is the on-resistance of the 10N45?
On-resistance (Rds(on)) is 0.6 Ω. Multiply by the square of your load current to estimate conduction loss.
What package does the 10N45 come in?
It is listed in TO-3. Verify the pinout of the specific variant, as one outline can carry different pin assignments.
What can I use to replace the 10N45?
No verified equivalents are listed yet. Choose a part of the same polarity that meets or exceeds every rating above and shares a compatible package and pinout.
Key Specifications
| Type | MOSFET |
|---|---|
| Channel Type | N -Channel |
| Drain-Source Voltage (Vds) | 450 V |
| Gate-Source Voltage (Vgs) | 20 V |
| Drain Current (Id) | 10 A |
| Drain-Source On-Resistance (Rds) | 0.6 |
| Rise Time (tr) | 50 nS |
| Output Capacitance (Coss) | 600 pF |
| Junction Temperature (Tj) | 150 °C |
| Package | TO-3 |
| Power Dissipation (Pd) | 150 W |
Equivalent & Replacement Parts
No verified equivalents are listed for 10N45 yet.